DISOLATE - LIKE GOLD TO GOLD

76% - COPPER
8% - THORIUM
12% - THULIUM
2% - PALLADIUM
1.8% - ARGON
0.2% - TELLURIUM

COPPER MANGENATE, BROKEN DOWN WITH SODIUM IONATE

INCLUDE PORTIONS OF BINDING HYDROCARBONS SUCH AS BLACK CHARCOAL AS DELIVERY

COMPLETE (BLEED OF IMPURITIES) PORTION OF THORIUM AND CAREFULLY MODERATE IT INTO THE COPPER PRELATE

THULIUM NEEDS TO BE MADE INTO A “SOLUTION” THAT ISN’T QUITE BOILED BUT IS MALEABLE ENOUGH TO MIX IN BORIUM ALGINATE

LET IT DISUME AND THEN BRING ITS TEMPERATURE BACK UP TO THE EXACT POINT WHERE THULIUM WOULD REGULARLY BOIL. IT WILL AGGRESS BUT NOT BOIL

CREATE A PART MIXTURE OF PALLADIUM, ARGON AND TELLURIUM FOR LATER POURING INTO THE DEPRESSED COPPER SOLUTION (MEANING IT HAS BEEN PURPOSELY BROUGHT BACK FROM BOILING TO NEAR-FORMING)

THE ARGON FIRST NEEDS TO BE “INGESTED” INTO THE PALLADIUM AT ITS EARLIEST POSSIBLE POINT, WHILE HEATING IT VERY SLOWLY AND CAREFULLY. IMMERSE THE ARGON AND ENSURE IT IS OPEN TO BREATHE WITH PLENTY OF VENTILATION

DO NOT HEAT THE PALLADIUM PAST THE POINT WHERE THE ARGON IS ACCEPTED. HOLD UNTIL IT IS INGESTED

ENSURE THAT NO VENTILLATION “FLUIDS” ARE ALLOWED TO PERSPIRE, FALL-BACK, ETC, INTO THE PALLADIUM WHILST IT IS ACCEPTING THE ARGON

AS SOON AS IT STABLISES, ADD THE TELLURIUM BUT DO NOT CHANGE THE TEMPERATURE OF THE SOLUTION

LET IT METABOLICALLY IMBIE ITSELF FOR A COUPLE OF HOURS. UNTIL IT’S COMPLETE PASSED THROUGH

TAKE THE THULIUM SOLUTION, BRING IT TO A TEMPERATURE BELOW BOILING, HOT ENOUGH TO INSTANTLY MELT TELLURIUM WHEN IT IS POURED ONTO IT

POUR CAREFULLY AND CONSISTENTLY INTO THE TELLURIUM SOLUTION. AS SLOW OR AS FAST AS IS NEEDED FOR THE REACTION OF THE MIXTURE TO REMAIN NON-VOLATILE

IT SHOULD NOT BE AGGRESSIVE, BUT IT COULD “FALL DOWN” IF DUMPED INTO THE OTHER MIXTURE

BRING THE COPPER SOLUTION UP TO JUST BELOW BOILING AND AGGITATE THE MIXTURE

BLEND IN THE TELLURIUM MIX. IMMEDIATELY AND RAPIDLY INCREASING THE TEMPERATURE PAST BOILING AS YOU DO, WHILST AGGITATING THE MIXTURE

THE ADDED SOLUTION WILL “FAST” THE COPPER SOLUTION RAPIDLY CHANGING IT’S STATE TOWARDS HARDENING. TO PREVENT THIS, THE TEMPERATURE NEEDS TO BE BROUGHT UP RAPIDLY AS IT'S TAKING PLACE

KEEP IT AS ‘MIXABLE’ AS POSSIBLE AND PUSH THE SOLUTION (UNTIL PROPERLY MIXED) TO A POINT WHERE IT EXCEEDS WHAT 'SHOULD BE' ITS BOILING POINT, BUT DOES NOT BOIL

YOU WILL HEAR ELECTRICAL TYPE NOISES. STATIC, HISSING OR CRACKLING COMING FROM WITHIN THE MIXTURE, WHILST IT ALSO BECOMES EASIER TO AGGITATE

WHEN YOU HEAR “POPPING” TYPE SOUNDS FROM WITHIN THE MIXTURE, YOU ARE AT THE RIGHT TEMPERATURE

MIX AS RAPIDLY AS YOU NEED TO KEEP IT AQEUOUS DURING THIS ENTIRE PROCESS

GET HYDROSOLIC ACID BY BOILING DOWN WATER INSIDE SOMETHING WITH A HEATING ELEMENT MADE OF HIGH-QUALITY TUNGSTEN

ADD A SMALL PORTION OF BI-CARBONATE SODA INTO THE WATER, AT ABOUT 1 PART PER 15
DO A ZERO-LOSS PRESSURISED REDUCTION OF POWDERED IODINE CRYSTAL IN PHOSPHOROUS ACID

PUT THE YIELD INTO SELENIUM POWDER TO “DRY IT OUT” THEN DO A VENTILATED REDUCTION IN SULPHURIC ACID

STRAIN IMPURITIES TO GET IODINE DICHLORIDE(CHLORITE)

PUT THE YIELD FROM THE TUNGSTEN-REDUCED WATER INTO A DISH AND MIX IT INTO A THICK/POWDERY PASTE WITH THE IODINE DICHLORIDE(CHLORITE)

ONCE THE DICHLORIDE(CHLORITE) AND TUNGSTEN YIELD ARE MIXED IN THE DISH, USE SALINE TO MAKE IT A SMOOTH, CREAMY PASTE

ADD A DASH OF VINEGAR AND MIX IT IN WELL. THEN IMMEDIATELY STRAIN THE IMPURITIES TO GET HYDROSOLIC ACID

SLOWLY POUR THE HYDROSOLIC ACID INTO THE VERY HOT COPPER COMPOSITE, AGGITATING THROUGHOUT

CONSISTENCY OF THE SOLUTION WILL SHIFT

THE SOLUTION WILL TURN A BROWNISH COLOUR, THEN A BLUE COLOUR WILL BLEED THROUGH

REDUCE THE TEMPERATURE WHEN THIS HAPPENS AS THE MIXTURE WILL QUICKLY BEGIN TO BOIL

KEEP THE TEMPERATURE JUST BELOW BOIL AND KEEP MIXING. KEEP BRINGING THE TEMPERATURE DOWN TO AVOID BOILING AS FAR AS YOU NEED TO (REDUCE HEAT QUICKLY AS YOU NEED TO)

LET THE MIXTURE COOL AND SETTLE IN LIQUID STATE. THE BROWN/BLUE COLOUR WILL TURN DARK-REDISH/BLUE AND TAKE ON A “OPAL” OR “PEARL SHELL” APPEARANCE

SIMMER THE MIX FOR A FEW HOURS

DISOLATE

THEN USE IT TO CAST COPPER PRODUCTS

DO NOT PLUNGE CASTINGS, OR OTHERWISE ARTIFICIALLY/RAPIDLY COOL THEM

NATURAL COOLING AT ROOM TEMPERATURE ONLY

WHILST CASTINGS ARE HOT AND AMORPHOUS, HARD-POLISH SURFACE WITH LITHIUM

COPPER SURFACE SHOULD (WILL) POLISH COLOURFULLY TO A OPAL-LIKE RAINBOW SHINE

FINISHED CASTINGS SHOULD NOT BE NON-TOXIC TO TOUCH OR USE, BUT DO NOT USE WITH FOOD OR DRINK

DISOLATE IS LIKE GOLD TO GOLD